View UPC1060_139133.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DATA SHEET
BIPOLAR ANALOG INTEGRATED CIRCUIT
PC1060
2.5 V HIGH PRECISION REFERENCE VOLTAGE CIRCUIT
DESCRIPTION
The PC1060 are high accuracy and low drift voltage references of 2.5 V output voltage. This IC can operate under wide range input voltage, and applied for 8 to 12 bits D/A converters.
FEATURES
* High Accuracy * Low Temperature Coefficient * Low Supply Current * Wide Supply Voltage Range * Low Load Regulation VO = 2.5 V 1 %
PIN CONFIGURATION
VO/ T 40 ppm/C
ICC 1.5 mA 4.5 V VIN 40 V REGL 10 mV
8-pin plastic DIP (7.62 mm (300)) PC1060C
INPUT 1 OUTPUT 2 GND 3 NC 4 8 NC 7 NC 6 NC 5 NC
ORDERING INFORMATION
Part Number Package 8-pin plastic DIP (7.62 mm (300))
PC1060C
EQUIVALENT CIRCUIT
INPUT R12 Q14 Q3 R8 Q10 Q8 Q2 Q1 R7 R6 Q11 Q6 Q12 Q15 Q9 Q16 R4 R9 OUTPUT R13 Q13 Q4 Q7
R2 R14 R15 R16 R17 R18 R1
C1
R11
R5
GND
The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version.
Not all devices/types available in every country. Please check with local NEC representative for availability and additional information.
Document No. G14607EJ4V0DS00 (4th edition) (Previous No. IC-1537) Date Published March 2000 NS CP (K) Printed in Japan
The mark
shows major revised points.
(c)
2000
PC1060
ABSOLUTE MAXIMUM RATINGS (TA = +25 C, unless otherwise specified.)
Parameter Input Voltage Total Power Dissipation Operating Ambient Temperature Storage Temperature Symbol VIN PT TA Tstg Ratings -0.3 to +40 350 -20 to +70 -55 to +125 Unit V mW C C
Caution Product quality may suffer if the absolute maximum rating is exceeded even momentarily for any parameter. That is the absolute maximum ratings are rated values at which the product is on the verge of suffering physical damage, and therefore the product must be used under conditions that ensure that the absolute maximum ratings are not exceeded.
TYPICAL CONNECTION
INPUT INPUT CIN 0.1 F 1 3 GND CO 0.1 F 2 OUTPUT OUTPUT
RECOMMENDED OPERATING CONDITIONS
Parameter Input Voltage Output Current Internal Power Dissipation Operating Ambient Temperature Symbol VIN IO PD TA -20 MIN. 4.5 0 TYP. MAX. 40 10 270 +70 Unit V mA mW C
Caution The recommended operating range may be exceeded without causing any problems provided that the absolute maximum ratings are not exceeded. However, if the device is operated in a way that exceeds the recommended operating conditions, the margin between the actual conditions of use and the absolute maximum ratings is small, and therefore thorough evaluation is necessary. The recommended operating conditions do not imply that the device can be used with all values at their maximum values.
2
Data Sheet G14607EJ4V0DS00
PC1060
ELECTRICAL CHARACTERISTICS (VIN = 15 V, IO = 0 A, TA = +25 C, unless otherwise specified.)
Parameter Output Voltage Output Voltage Change Temperature Coefficient of Output Voltage Line Regulation REGIN 15 V VIN 40 V 4.5 V VIN 15 V Load Regulation Ripple Rejection Output Noise Voltage REGL R*R Vn 0 A IO 10 mA 5 V VIN 40 V, f = 120 Hz 4.5 V VIN 40 V, 0 A IO 10 mA, PT 350 mW Short Circuit Current Circuit Current IOshort ICC VO = 0 V 17 1.5 mA mA 90 80 4.5 3.0 10 mV mV mV dB Symbol VO Test Conditions MIN. 2.475 0 C TA 70 C 0 C TA 70 C TYP. 2.5 MAX. 2.525 7.0 40 Unit V mV ppm/C
VO VO/ T
Vp-p
Data Sheet G14607EJ4V0DS00
3
PC1060
TYPICAL CHARACTERISTIC (TA = +25 C, unless otherwise specified. Nominal)
PT vs TA
0.5
VO vs TA
VIN = 15 V, IO = 0 A
0.4 200 C/W 0.3
VO - Output Voltage Cange - mV
PT - Total Power Dissipation - W
0
0.2
0.1
-5
0
25 50 75 100 125 TA - Operating Ambient Temperature - C
-20
60 80 0 20 40 TA - Operating Ambient Temperature - C
VO vs IO
VIN = 15 V
VO vs VIN
TA = +50 C IO = 0 A TA = +25 C TA = +70 C 0
VO - Output Voltage Cange - mV
TA = +25 C 0 TA = +70 C TA = 0 C
VO - Output Voltage Cange - mV
TA = +50 C
TA = 0 C
-5
TA = -20 C
-5
TA = -20 C
0
2
4 6 8 IO - Output Current - mA
10
0
10 20 30 VIN - Input Voltage - V
40
ICC vs TA
1.20 VIN = 15 V, IO = 0 A 1.15 1.15 1.20
ICC vs VIN
IO = 0 A TA = -20 C
ICC - Circuit Current - mA
ICC - Circuit Current - mA
1.10
1.10
TA = +25 C
1.05
1.05 TA = +70 C
1.00
0 -20
60 80 0 20 40 TA - Operating Ambient Temperature - C
0
10 20 30 VIN - Input Voltage - V
40
4
Data Sheet G14607EJ4V0DS00
PC1060
PACKAGE DRAWING
8-PIN PLASTIC DIP (7.62mm(300))
8 5
1
A
4
K J I P L
H G F D N
M
C B M R
NOTES 1. Each lead centerline is located within 0.25 mm of its true position (T.P.) at maximum material condition. 2. ltem "K" to center of leads when formed parallel.
ITEM A B C D F G H I J K L M N P R
MILLIMETERS 10.16 MAX. 1.27 MAX. 2.54 (T.P.) 0.500.10 1.4 MIN. 3.20.3 0.51 MIN. 4.31 MAX. 5.08 MAX. 7.62 (T.P.) 6.4 0.25 +0.10 -0.05 0.25 0.9 MIN. 015 P8C-100-300B,C-2
Data Sheet G14607EJ4V0DS00
5
PC1060
RECOMMENDED SOLDERING CONDITIONS
When soldering this product, it is highly recommended to observe the conditions as shown below. If other soldering processes are used, or if the soldering is performed under different conditions, please make sure to consult with our sales offices. For more details, refer to our document "Semiconductor Device Mounting Technology Manual" (C10535E). Type of Through-hole Device
PC1060C : 8-pin plastic DIP (7.62 mm (300))
Process Wave soldering (only to leads) Conditions Solder temperature: 260C or below, Flow time: 10 seconds or less.
Caution For through-hole device, the wave soldering process must be applied only to leads, and make sure that the package body does not get jet soldered.
REFERENCE DOCUMENTS
Semiconductor Device Mounting Technology Manual Semiconductor Selection Guide -Products and Packages-
C10535E X13769X
6
Data Sheet G14607EJ4V0DS00
PC1060
[MEMO]
Data Sheet G14607EJ4V0DS00
7
PC1060
[MEMO]
* The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. * No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. * NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. * Descriptions of circuits, software, and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software, and information in the design of the customer's equipment shall be done under the full responsibility of the customer. NEC Corporation assumes no responsibility for any losses incurred by the customer or third parties arising from the use of these circuits, software, and information. * While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. * NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance.
M7 98. 8

▲Up To Search▲

Price & Availability of UPC1060

	To Download UPC1060 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .